Looking for:
Eliminator sprayer model 1401e manual |
Eliminator sprayer model 1401e manual.Eliminator 1401E 1 gal Handheld Sprayer
Easy push pressure plunger. Made well and does the job well. Would recommend highly. It only holds a gallon so is easy to carry around and spray.
The seal has worked well so it's easy to pump up Nice sprayer at a good price! Does a great job for what I use it for.
Perfect size. I love the easy twist pressure release vent. Adjustable nozzle works great! Skip to main content. Eliminator E Pump Sprayer - 1 Gallon 4. About this product. Make an offer:. Stock photo. Brand new: Lowest price The lowest-priced brand-new, unused, unopened, undamaged item in its original packaging where packaging is applicable. Buy It Now. Add to cart. Make Offer. It features a polyethylene wand with an adjustable nozzle that allows you to modify the flow for precision application in tight spots.
Its low-effort pump makes the Eliminator Sprayer easy to use and highly efficient and it has a reinforced hose that s durable for repeated uses. See all 8 brand new listings.
About this product Product Identifiers Brand. Show More Show Less. Condition: New New. See all 8 - listings for this product. Ratings and Reviews Learn more.
The valve must be designed for the proper MAWP and flow requirements of the system. Consult API Standard for tank protection sizing procedures. An improperly specified or functioning relief valve may result in structural damage to the tank or system. In the event of a diaphragm failure, the pilot valve will vent pressure to the atmosphere, causing the pressure relief valve to fail in the OPEN position.
Pressure may be vented slowly, simulating the action of a modulating pilot. Under these conditions, somewhat greater overpressure may be required to produce the full flow capacity of the relief valve. Pilot valve set pressure and blowdown are set at the factory per purchase specifications. The set pressure and range of adjustability are stamped on the nameplate. DO NOT attempt to readjust the set pressure beyond the limits specified on the nameplate and in Table 2.
It must be kept open and unobstructed to ensure that the pilot "senses" actual tank pressure. For applications where tank vapors may condense or "polymerize" in the sense tube or pilot valve, a nitrogen purge may be required to prevent internal obstruction of the tube. Consult Groth Corporation for recommendations. DO NOT attempt to remove the pilot valve from the pressure relief valve without removing or isolating the relief valve from the system.
After isolating the relief valve, bleed all pressure from both relief and pilot valves before removing the pilot valve. Both pilot and pressure relief valve are exposed to process vapors. Observe all plant procedures and Material Safety Data Sheets for the products in the system when inspecting, adjusting or servicing the valves. Vents on the body and spring bonnet of the pilot valve must be clean and unobstructed for proper and safe operation of the valve.
These vents should be inspected periodically. Back out set pressure adjusting screw to relieve all spring pressure before removing the spring bonnet.
Blowdown needle chamber is exposed to system pressure. The screw may be adjusted from nearly contacting the seat screw bottomed out for snap action to partially retracted for maximum modulation. The screw is retained by the blowdown bushing. DO NOT remove the blowdown bushing while under pressure. The tank pressure required to discharge the normal or emergency venting requirements of the tank will be increased by the amount of back pressure in the discharge header.
Maximum possible discharge header pressure must be considered when sizing the pressure relief valve. The pilot valve or pilot operated pressure relief valve is packaged and supported to prevent damage or contamination during shipping. It should be similarly protected during subsequent handling and storage.
Always keep all ports plugged to prevent intrusion of foreign materials. Before installation, inspect the unit visually. If there are indications of physical damage or internal contamination, the valve must be disassembled, cleaned and inspected before installation.
The spring adjustment cap and blowdown screw locknut must be secure. Report any shipping damage to your carrier. There should be no block valve or other restriction between the pilot valve and the actuator. Wrap all pipe threads with fluoropolymer tape or apply a suitable pipe thread sealant sparingly.
Before connecting sense line, backflow compressed air through line and pick-up fitting in relief valve to assure that no obstruction exists. Connect sense line to relief valve and pilot valve with no in-line block valve or other restriction. If a check valve is used in the sense line for backflow prevention, make sure it is unrestricted and installed with the correct flow direction Fig 8. The same procedures and precautions apply if a remote sense line is used.
Set pressure and blowdown adjustment may be done on the test bench following the procedure on page 11 or on the relief valve. The initial set pressure and spring range can be found on the pilot valve nameplate. Both relief pressure and blowdown are set at the factory to comply with the specification on the purchase order.
The range of adjustment will depend on the spring installed and will be stamped on the nameplate. The pressure setting may be changed within the designed range either while on line or in a service shop. Observe the proper setting and testing procedure in this manual.
Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Groth E User Manual Download for 1. Tank Installation - Safety Equipment 2 2. Pilot Valve Function-Shut off Condition 2 3. Operation - Closed Position 5 4. Operation - Open, Snap Action 5 5.
Operation - Open Modulating 5 6. Operation - Reseat, Snap Action 6 7. Operation - Reseat Modulation 6 8. Options - Vent Piped to Discharge Header 6 9. Options - Field Test Connection 7 Body Sub - Assembly 9 Stem Sub - Assembly 10 Test Apparatus 11 Exploded Assembly 13
